You will find five quick ways to framing.
Stage one – Ways to Reduce Mats
Including a color border (the mat) around your artwork improves the image and supplies a restful region amongst the graphic as well as photograph frame. The color and dimensions in the mat board has to be determined initial, as this can ascertain the overall dimensions of your respective picture body. You begin by calculating the exterior size of the mat.
To cut the mat make use of a good quality bevel mat cutter and ruler. You will find several slicing systems to accommodate numerous budgets and talent concentrations, including the Mat Master Product 660 for the hobbyists, for the Mat Grasp 860B or 1060B for the eager property image framer.
Mark the borders to be slice within the back again with the mat board.
Ensure that the mat will include the perimeters in the artwork, by subtracting approx. 3mm or 1/8″ through the graphic measurement (size & width). Slash the mat following the instructions for your mat cutter. Attach the picture for the mat using 2 small pieces of acid free tape around the top edge only.
Action 2 – The best way to Reduce the picture Frame
How much picture rustic picture frames body moulding material will I need? Carefully measure the image and mat you wish to body. Add an extra (3mm) for “play” to ensure the picture fits easily into the finished photograph frame.
Add the size (L) and width (W) together, then multiply the total by 2 to give you the overall duration. You also have to allow to the mitre cuts, so multiply the width (W2) of your moulding by 10 and add this to your total.
(L W) x 2 (W2 x 10) = TOTAL
Producing the 45 degree mitre reduce in your framing material is most important – your joining will only be as very good as your chopping. Always make use of a high quality manual Mitre Saw… we recommend the Proman hand saw which is made in Sweden as the best on the market. Electric powered Drop Saws are not ideal for chopping small delicate photo frames.
Very good Measure System helps to make measuring easy and eliminates many mistakes. Once you have slice the initial mitre, slide the picture frame material along to your required duration about the measuring scale, and set the stop. You are now ready to chop the first 2 pieces of one’s image body. Change the settings to chop the other 2 sides from the frame.
Reducing one side for a frame is quick.
Reducing the second side for being be the same as the first, is the hard part. With the FrameCo Ezy-Measure System you can minimize accurately every time.
Phase 3 – How you can Clamp Frames
How do you Clamp the Body? Clamping the body tightly is essential for good joining. You can use the a Cord Clamp, or the Steel Strap Clamp to secure the picture frame ready for joining.
The advantage on the Strap Clamp is that you can see all the four corners of the photograph body clamped together before joining. So alignment from the corners is quick.
All corners should match up evenly. Apply a little wood glue to all corners of your body for added strength. Carefully tension the clamp creating sure that the corners are aligned then secure the clamp tightly.
You are now ready for joining.
Action 4 – Ways to Join Frames
Most picture frames are joined with a V-Nail. This is the easiest method and it is what the professional photo framer uses. The FrameCo PushMaster joining tool, inserts V-Nails into the corner on the frame. Two V-Nails in each corner is usually all that is necessary.
The PushMaster can be used by hand alone on most photograph frames, or you can tap the PushMaster with a mallet if the frame is hardwood. The PushMaster can be upgraded to the BenchMaster® which will insert V-Nails into the harderst of timbers.
V-nails: How do they work?
Upon entry, the sides in the V-Nail are deflected outwards. As it pulls back into its original shape, the join is pulled together. The little curl within the edge in the V-Nail locks the nail into the grain of your timber. Glue alone is not sufficient for strong stable joints, by incorporating a V-Nail you achieve a strong, tight joint. Which V-Nail measurement . . . You utilize a V-Nail about 1/2 the body height.
Sizes are: 7mm – 1/4″, 10mm – 3/8″, 12mm – 1/2″, 15mm – 5/8″
Phase 5 – How to Finish Frames
Take the empty image body to a glass merchant and have them reduce a piece of glass for you. If you wish to cut glass yourself use a top quality oil filled cutter, or the Glass Cutter. Use only 2mm plain or non-reflective glass.
Fome Core is the ideal backing board as it is light weight, acid free and straightforward to chop. You can also use 3mm MDF or cardboard. Place the empty frame face down and insert the glass, then the matted photograph and lastly the backing board.
Use the PushMaster to insert brads or flexipoints into the rear of your respective photo body to hold everything in place.
Use Backing Nails for large frames or heavy items. Flexipoints are flexible and ideal for needlework or when you want to re move the image, eg. photo frames.
To seal the artwork in the frame, tape over the brads/flexipoints using a very good good quality backing tape. This can prevent dust or insects getting into the image.